Orders placed by 14:00 on a business day leave Poland the same day. Free shipping from €100
Product question?Write to us
RUO

All products are chemical reagents for scientific research only. Not for consumption or use in humans or animals. Policy

Reference

Reference: glossary of analytical terms on a label

16 November 2026 · 5 min read

A reagent label and the certificate that travels with it use a small, fixed vocabulary. Most of it is precise, and several terms mean narrower things than they appear to. The definitions below are alphabetical and kept to what each word actually denotes. Terms outside the analytical set are collected on the glossary page.

Area percent

The share of the total integrated peak area in a chromatogram that belongs to one peak, written as a percentage. It describes the detected signal, not the contents of the vial by mass. Anything the detector does not respond to, and anything that does not leave the column, is absent from the total.

Average mass

The mass of a molecule calculated from the standard atomic weights of its elements, which are averages across natural isotopic abundance. It is the figure usually quoted for larger molecules, and the one matching a broad, unresolved peak.

CAS number

A registry identifier assigned by the Chemical Abstracts Service to a specific substance, used for unambiguous identification in catalogues and safety documentation. Not every peptide carries one, and a salt form can have a different number from the free acid, so an absent number is not a fault.

High performance liquid chromatography (HPLC)

A separation technique in which the sample is carried by a pressurised liquid through a column packed with fine particles. Components travel at different rates and a detector records what leaves the column. The output is a chromatogram: detector response plotted against elution time.

Hygroscopic

Describes a material that takes up water from the surrounding air. Lyophilised peptides are hygroscopic, which is why a vial is brought to room temperature before the cap comes off. Open a cold vial and moist air condenses inside it, and that water stays behind.

Lot

The identifier for one production and packaging run. It is the link between the vial in your hand and the analytical documentation issued for that batch. Two vials sharing a product name but carrying different lots are different materials for record keeping.

Lyophilised

Freeze dried. The solution is frozen and the water removed by sublimation under reduced pressure, leaving a dry cake or film. Its appearance follows the fill volume, vial shape and drying cycle, so it varies between lots.

Mass spectrometry

A technique that ionises molecules and measures the mass to charge ratio of the resulting ions. For peptides, electrospray ionisation produces a series of multiply charged ions, from which the neutral mass is calculated. It addresses identity, which a purity figure does not.

Molar mass

The mass of one mole of a substance, in grams per mole. It converts between mass and amount of substance, the number required to express a solution in molar rather than mass concentration. For a salt form, check whether the figure includes the counter ion.

Molecular formula

The count of each element in one molecule. For a peptide it is normally written for the free acid or free base, with any salt form stated separately. The salt changes the mass without changing the sequence, so check which the figure means.

Monoisotopic mass

The mass of a molecule calculated using the lightest and most abundant isotope of each element. It corresponds to the first peak of a resolved isotope cluster. It is lower than the average mass, and the gap widens as the molecule grows.

Net peptide content

The proportion of the weighed material that is peptide. The remainder is counter ions, residual water and residual solvent. It is a determination separate from chromatographic purity, commonly by amino acid analysis or elemental nitrogen determination, and it is the figure that matters when the work depends on amount rather than identity.

Purity

The share of the chromatographic signal assigned to the main component, normally reported as area percent at a stated detection wavelength. The wavelength matters: a component that absorbs weakly at it contributes little area whatever its amount.

Research use only

A supply classification. The material is sold as a chemical reagent for laboratory research. It is not a medicine, a food, a cosmetic or a veterinary product, it is not qualified for use in or on humans or animals, and no effect in a living organism is claimed or implied. The scope is set out on the research use only page.

Residual solvent

Solvent left in the dried material from synthesis, purification and drying. In peptide work the usual residues are acetonitrile, trifluoroacetic acid and water. Residual solvent adds to the mass on the balance without adding peptide.

Reversed phase

A chromatographic mode in which the stationary phase is non polar and the mobile phase is polar, typically water mixed with an organic solvent and run as a gradient. Components elute broadly in order of increasing hydrophobicity. It is the standard mode for peptide purity work.

Terms that are often confused

These look alike They are not the same
Purity, net peptide content a share of detected signal against a share of weighed mass
Identity, purity identity says which molecule, purity says how much of the signal is one species
Monoisotopic mass, average mass different isotope conventions, so the two figures never match exactly
Lot number, catalogue reference the reference names the product, the lot names one batch of it

How this shows up at the bench

Quote the method with the number. The same sample on a different gradient gives a different area percent, so a figure without its conditions cannot be compared with another.

Keep the lot with the figure. Every value on a certificate belongs to one batch, tested once, on one date, and says nothing about the next batch. Which values are reported, and how, is covered on the quality page.