Orders placed by 14:00 on a business day leave Poland the same day. Free shipping from €100
Product question?Write to us
RUO

All products are chemical reagents for scientific research only. Not for consumption or use in humans or animals. Policy

Knowledge base: method notes

Short, practical notes on handling research reagents. Protocols, reference sheets and checklists, written for the bench rather than for the literature.

24 notes

Reference

  1. Choosing a solvent for a peptide reagent Bacteriostatic water, sterile water and dilute acetic acid compared: what each is for, what the preservative does and when an acid solvent helps.
  2. Concentration, volume and molarity for a vial The arithmetic a laboratory repeats daily: mass over volume, mg/ml converted to millimolar, target volumes and dilution series, with worked examples.
  3. Glossary of analytical terms on a label Plain definitions of the analytical terms found on a peptide reagent label and certificate, from area percent to reversed phase chromatography.
  4. Lyophilisation and the cake in the vial What freeze drying does to a vial, why the dried cake looks different between lots, and the few times its appearance is worth stopping for.
  5. PH, buffers and peptide solubility How amino acid composition sets peptide charge, why solubility falls near the isoelectric point, and what a buffer does in a working solution.
  6. Records that make an experiment reproducible The record set that links a result back to a defined material: lot, storage, reconstitution, solvent lot, aliquots, thaw count and operator.
  7. Vial formats, crimp caps and the seal The anatomy of a serum vial: glass body, elastomeric stopper, aluminium crimp and flip off cap, and what repeated punctures do to the seal.
  8. Water grades in the laboratory What distilled, deionised, purified, ultrapure, sterile and bacteriostatic water each describe, what is removed and where each grade belongs.

Protocol

  1. Aliquoting a reconstituted vial and limiting freeze thaw A method note on dividing a reconstituted vial into working portions: how to size an aliquot, what to label and why repeated thawing costs material.
  2. Disposing of reagents and used vials General laboratory practice for reagent waste: segregating sharps and glass, handling leftover solution, decontaminating a surface and keeping a record.
  3. Labelling vials and keeping a reagent log The six fields a frozen tube label must carry, which label materials survive a freezer, and how to keep a reagent log that stays accurate.
  4. Planning quantities for a series of experiments How to work backwards from runs per experiment to vials ordered, allowing for repeats, dead volume and the working life of a reconstituted solution.
  5. Reconstituting a lyophilised peptide vial A bench method for dissolving a lyophilised peptide vial: choosing the volume, technique at the stopper, and what haze, foam or a floating cake means.
  6. Weighing and transferring milligram quantities How to weigh and transfer milligram amounts of solid reagent without losing the reading to static, draughts, temperature or moisture uptake.
  7. What to do when a peptide will not dissolve An ordered path for a peptide that will not go into solution: what to check first, what to change next, and what to avoid at every step.

Quality control

  1. Confirming peptide identity by mass spectrometry What a mass spectrum adds to a purity figure: calculated against measured mass, monoisotopic and average, charge states and common adducts.
  2. Reading an HPLC purity chromatogram How a reversed phase HPLC trace of a peptide is read: retention time, peak shape, baseline, and why area percent is not the same as mass percent.
  3. What a certificate of analysis tells you A line by line reading of a certificate of analysis: what each section reports, what the methods actually measure, and what the document does not cover.
  4. Where impurities in a synthetic peptide come from Where the related substances in a synthetic peptide come from: deletion sequences, truncated chains, protecting groups, scavengers, salts and water.

Storage

  1. Protecting a reagent from moisture and light A bench protocol for equilibrating a cold vial before opening, keeping a hygroscopic solid dry, and shielding light sensitive material.
  2. Cold chain, ambient shipping and what degrades Why lyophilised peptides ship at ambient temperature, what actually drives degradation, and what to do with a parcel the day it arrives.
  3. Storage temperatures for peptide reagents A reference table of storage zones for peptide reagents, what each temperature suits, and why the date a vial was opened matters most.

Checklist

  1. Equipment and consumables for a peptide bench Equipment and consumables for a bench handling lyophilised peptides, grouped by purpose, with the reason for each item and what fails without it.
  2. Receiving, inspecting and logging a delivery A goods in checklist for reagent parcels: what to inspect on the box, the vials and the labels, what to record, and what to do when something is wrong.