Orders placed by 14:00 on a business day leave Poland the same day. Free shipping from €100
Product question?Write to us
RUO

All products are chemical reagents for scientific research only. Not for consumption or use in humans or animals. Policy

Protocol

Protocol: aliquoting a reconstituted vial and limiting freeze thaw

21 November 2026 · 3 min read

A vial of lyophilised peptide is stable for a long time. The solution made from it is not, and most of what a laboratory loses between reconstitution and the end of a series of experiments is lost at the freezer door. This note covers the practical side of dividing a reconstituted vial into portions.

Why the number of thaw cycles matters more than the time in storage

Every freezing and thawing cycle puts a peptide solution through the same sequence: ice crystals form, the concentration of everything dissolved in the remaining liquid water rises, the pH of the buffer shifts, and the peptide spends a period at an interface between ice and liquid. Adsorption onto the tube wall happens at every one of those steps.

The practical consequence is that a vial thawed ten times has been through ten of those cycles regardless of whether the whole process took a week or six months. A solution divided into ten portions at the moment of reconstitution goes through one cycle per portion.

Sizing a portion

Work backwards from a single session rather than from the vial.

  1. Estimate the volume one experiment consumes, including what stays in the pipette tip and what is lost in a dilution series.
  2. Add a margin, commonly a quarter of that volume, for a repeat.
  3. Round to a volume that is comfortable to pipette. Portions below 20 microlitres are difficult to recover from the bottom of a tube.
  4. Divide the reconstitution volume by the portion size to get the number of tubes.

A 10 mg vial brought up in 5 ml gives 2 mg per ml. Portions of 250 microlitres from that vial yield twenty tubes of 0.5 mg each.

Choosing tubes

Low binding polypropylene tubes exist because peptides adsorb onto ordinary plastic, and the loss is proportionally larger in dilute solutions and in small volumes. Glass has the same problem and adds the risk of breakage at low temperature. Whatever is used, use the same type throughout a series, so that an unexplained difference between two experiments is not simply a difference in tube.

Fill a tube no more than four fifths of the way: water expands as it freezes and a full tube can force its own cap.

Labelling

A tube that cannot be identified in six months is an empty tube. The minimum that survives frost and a gloved hand:

Field Example Why
Substance BPC-157 obvious at the bench, not obvious in a box of forty tubes
Concentration 2 mg/ml removes the need to reconstruct the arithmetic later
Solvent bacteriostatic water a later anomaly may belong to the solvent
Lot number from the vial label links the tube to the analytical documentation
Date of reconstitution 21/11/2026 the clock on stability starts here, not at the date of purchase

Write with a solvent resistant marker on a label designed for low temperature, or on cryogenic tape. Pen on tape peels off in a freezer within weeks.

Thawing

Thaw a portion in the hand or in a rack at room temperature rather than in a water bath, and use it once it is liquid rather than letting it warm further. Mix by inverting the closed tube a few times; a vortex drives a peptide into foam, and the air to liquid interface is another surface to adsorb onto.

Return anything unused to 2 to 8 degrees Celsius only if the portion will be used within the period your own protocol allows. Refreezing a thawed portion defeats the point of having aliquoted it.

A short checklist

  • Aliquot at the moment of reconstitution, not after the first experiment.
  • One portion equals one session.
  • Low binding tubes, filled to four fifths.
  • Label carries substance, concentration, solvent, lot and date.
  • Thaw gently, mix by inversion, do not refreeze.

Solvents for reconstitution are listed under lab supplies in our catalogue. The concentration calculator converts between vial size, volume and concentration if you would rather not do the arithmetic by hand.