Protocol
Protocol: reconstituting a lyophilised peptide vial
3 November 2026 · 5 min read
A lyophilised vial contains a few milligrams of solid and a partial vacuum. Most of what decides whether the cake dissolves cleanly, or whether you spend the rest of the morning looking at a hazy tube, happens in the first minute after the solvent enters. The sequence below is ordinary laboratory practice written out with the reason behind each step, because a step whose purpose is unclear is the first one that gets skipped.
Before anything is opened
- Take the vial out of cold storage and let it stand closed until it reaches room temperature, usually twenty to thirty minutes for a small vial. Cold glass pulls moisture out of the air, and a stopper pierced while the contents are still cold collects condensation on the inside of the vial. That water is not measured, so the final concentration is no longer the one you calculated.
- Look at the cake before adding anything. A compact white or off white plug at the bottom is the normal appearance. A cake that has shrunk to a thin film, has changed colour, or is lying loose as powder is still usable in most cases, but note the appearance now, because a note written after a failed experiment is worth very little.
- Decide the volume and write it down. Reconstitution is not reversible: once the solvent is in, the concentration is fixed.
- Wipe the stopper with an alcohol wipe and let it dry. A wet stopper carries alcohol into the vial on the needle.
Choosing the volume
Two things set the volume. The first is the concentration you want to work at. The second is how much liquid you can actually pipette accurately, and the smallest reliable volume on your pipette is the real constraint in most laboratories.
| Peptide in the vial | Solvent added | Resulting concentration |
|---|---|---|
| 2 mg | 1 ml | 2 mg/ml |
| 2 mg | 2 ml | 1 mg/ml |
| 5 mg | 1 ml | 5 mg/ml |
| 5 mg | 2.5 ml | 2 mg/ml |
| 5 mg | 5 ml | 1 mg/ml |
| 10 mg | 2 ml | 5 mg/ml |
| 10 mg | 5 ml | 2 mg/ml |
| 10 mg | 10 ml | 1 mg/ml |
A concentrated stock saves freezer space and can always be diluted later. A dilute stock wastes less material in the pipette tip and in the dead volume of a dilution series. If the arithmetic for an awkward vial size is not obvious, the concentration calculator does the conversion between vial mass, volume and concentration.
The procedure
- Draw the chosen volume of solvent. For a vial that will be entered once, sterile water is the usual choice. For a vial that will be entered several times, bacteriostatic water contains a preservative, which is what makes repeated entry reasonable.
- Insert the needle through the centre of the stopper at a slight angle. The centre is thinner and reseals better than the edge.
- Direct the stream at the glass wall just above the cake, not onto the cake itself. Let it run down. A jet fired straight into a lyophilised plug breaks it apart mechanically and drives air into the solution, and both make the result harder to read.
- Release the plunger slowly and let the vacuum draw the liquid in at its own rate rather than forcing it.
- Withdraw the needle and let the vial stand upright for two to three minutes without touching it. Most of the cake dissolves on its own during this pause. Agitation added too early is agitation you did not need.
- If solid is still visible, roll the closed vial slowly between both palms. Do not shake and do not vortex. Shaking creates an air to liquid interface over the whole inner surface, and peptides adsorb at that interface.
- Hold the vial against a dark background and then a light one, and look through the liquid for anything undissolved.
- Label the vial with the concentration, the solvent and the date, then move it to the storage temperature given on the product documentation.
What goes wrong
Foam on the surface. Almost always caused by shaking, or by pushing the solvent in too fast. Let the vial stand until the foam collapses before judging anything else. Foam itself is not contamination, but the handling that produced it is worth correcting.
The solution looks hazy or cloudy. A haze that does not clear after standing suggests the peptide has not fully dissolved rather than that something is wrong with the solvent. A poorly soluble peptide often needs a different solvent rather than more force, which is covered in the reference note on solvent choice.
A fragment of cake floats on the surface. Common and usually harmless. Swirl gently and give it time. A fragment that refuses to wet after several minutes is a solubility problem, not a mixing problem.
Material clings under the stopper. Tap the vial gently on the bench before adding solvent so that loose powder falls to the bottom. Material left in the neck is material missing from your stated concentration.
Nothing dissolves at all. Stop and check the label against what you expected to receive. Reaching for heat or a vortex at this point usually costs more than it recovers.
Checklist
- Vial at room temperature before the stopper is pierced.
- Volume decided and written down first.
- Solvent aimed at the glass wall, never at the cake.
- Stand two to three minutes, then swirl, never shake.
- Inspect against both a light and a dark background.
- Label carries concentration, solvent and date.
This procedure describes the handling of a chemical reagent at the bench and nothing beyond that, a scope set out under research use only.