Orders placed by 14:00 on a business day leave Poland the same day. Free shipping from €100
Product question?Write to us
RUO

All products are chemical reagents for scientific research only. Not for consumption or use in humans or animals. Policy

Reference

Reference: vial formats, crimp caps and the seal

10 November 2026 · 5 min read

Almost every lyophilised peptide reagent arrives in the same container: a small glass vial with a rubber stopper held down by an aluminium ring and a coloured plastic button on top. The format is familiar enough that its parts are rarely examined, which keeps one misunderstanding alive: the cap is not the seal.

The four parts

Part Usual material What it does
Body Type I borosilicate glass holds the contents and resists attack by them
Stopper elastomeric closure, commonly a butyl rubber forms the seal and reseals after a puncture
Crimp aluminium ring, rolled under the neck flange holds the stopper compressed against the glass
Flip off button plastic disc in the centre of the crimp a dust cover over the puncture area, nothing more

Serum vial necks come in a small number of standard finishes, commonly 13 mm and 20 mm, which is why stoppers and crimps from one supplier fit vials from another. The neck finish, not the volume of the vial, decides whether a closure fits.

The glass body

Borosilicate is used because it is chemically resistant and releases very little into the contents. That matters most for solutions held for weeks: glass that leaches shifts the pH of a weakly buffered solution, and pH changes solubility.

The body is also a modest pressure vessel. Many lyophilised vials are stoppered at the end of the drying cycle while the chamber is still under reduced pressure, or after backfilling with an inert gas, so the vial may hold a partial vacuum or an atmosphere that is not room air. That is deliberate: it keeps oxygen and water vapour away from a dry, hygroscopic solid.

The stopper is the seal

The seal forms where the elastomer meets the glass, in two places: the plug inside the neck bore, and the flange pressed down onto the flat top face of the neck. Compression holds both. Nothing else in the assembly touches the contents.

A lyophilisation stopper usually has slots or legs on the plug. During drying it sits raised, the slots letting water vapour leave the vial, and at the end of the cycle the chamber shelf presses every stopper fully home at once. The same component is first a vent and then the closure.

The crimp holds the compression

The aluminium ring is rolled under the lip of the neck so that it cannot lift. Its job is mechanical: it keeps the stopper compressed for the life of the vial. If the crimp is loose, turns freely under light pressure, or has lifted anywhere around the neck, that compression is no longer guaranteed and the seal cannot be relied on, however intact the stopper looks.

Never prise a crimp off to make access easier. It removes the seal, leaves a sharp edge of aluminium, and turns the vial into an open container that cannot be closed again.

The flip off cap is not a seal

The plastic button is a dust cover. Flipping it off exposes the central disc of the stopper, the area intended for puncture, and it cannot be put back on.

Two consequences follow. A vial whose button is already gone has had its puncture area exposed to room air for an unknown period, so wipe the stopper with a suitable alcohol and let it dry before entering. And the colour of the button has no standard meaning: it is whatever the filler chose, so reading colour as a code for strength, contents or solvent is a way to pick up the wrong vial.

What repeated punctures do

An elastomer reseals because it is compressed. Every puncture spends a little of that capacity.

  • Channels. Repeated entries through the same spot leave a path that no longer closes fully, so the vial slowly exchanges air with the room.
  • Coring. A needle can cut a disc of rubber out of the stopper instead of parting it. The fragment falls into the contents and the hole does not reseal. A fragment visible in a vial means that vial is finished.
  • Loss of the barrier. Once air exchanges freely, so does water vapour, which matters for a hygroscopic solid and for a solution expected to last weeks.

Coring is reduced by entering perpendicular to the stopper face, at the centre, with a sharp needle in one steady movement. Multiple entries are also why a preserved solvent such as bacteriostatic water exists, though a preservative addresses microbial growth, not the mechanical state of the stopper.

Keep a count of entries on the vial label. Nobody remembers the number, and the count is the only honest basis for retiring a vial.

When a vial is no longer a sealed reagent

Treat any of these as the end of the vial’s life as a sealed container:

  1. The crimp is loose, lifted, or has been removed.
  2. The vial shows no inward rush on entry where it should hold a partial vacuum.
  3. Rubber fragments are visible in the contents.
  4. The stopper face is visibly chewed, cratered or split.
  5. The glass shows a chip or a star fracture at the neck or base.
  6. Liquid is tracking around the stopper flange.

None of these mean the chemistry inside has changed. They mean the container can no longer be assumed to protect it, so the contents become open material with a working life measured from the breach. Terms above are defined in the glossary.

What goes wrong

  • Treating the flip off cap as proof of integrity. It proves only that the puncture area was covered.
  • Not counting entries. The vial looks the same at entry fifteen as at entry two, and it is not.