Orders placed by 14:00 on a business day leave Poland the same day. Free shipping from €100
Product question?Write to us
RUO

All products are chemical reagents for scientific research only. Not for consumption or use in humans or animals. Policy

Quality control

Reference: confirming peptide identity by mass spectrometry

10 November 2026 · 5 min read

A purity figure answers one question: of the material the detector can see, how much is a single species. It says nothing about which species that is. A sharp peak at 99 percent is equally consistent with the intended peptide and with a different peptide of similar polarity. Identity is a separate determination, and mass spectrometry is the usual way to make it.

Calculating the expected mass from the sequence

The arithmetic is additive. Each amino acid contributes its residue mass, which is the free amino acid minus the water lost in forming the peptide bond. Sum the residue masses across the sequence and add one water for the two free ends, and you have the mass of the linear peptide with a free N terminus and a free acid C terminus.

Modifications are then applied as fixed corrections:

  • An amidated C terminus replaces OH with NH2, so the mass drops by about 1.
  • An acetylated N terminus adds about 42.
  • Each disulfide bond costs two hydrogens, so the mass drops by about 2 per bond.

The same sequence as a free acid and as an amide are different substances with different masses, so a calculated mass means nothing until the terminal chemistry is stated. Check which form the certificate assumed.

Monoisotopic and average mass

Elements occur as mixtures of isotopes, so a peptide does not have one mass but a distribution of them.

The monoisotopic mass uses the lightest and most abundant isotope of each element: carbon 12, hydrogen 1, nitrogen 14, oxygen 16. It corresponds to the first peak of the isotope cluster, the one in which no atom happens to be a heavier isotope.

The average mass uses the natural abundance weighted average of each element. It corresponds to the centre of the isotope envelope.

Which applies depends on the instrument and the size of the peptide. Where individual isotope peaks are resolved, and for peptides of modest size, the monoisotopic value is the right comparison and the match can be tight. For larger chains the envelope holds many peaks of similar height, the monoisotopic peak becomes small and hard to pick out, and the practical comparison is against the average mass. Comparing a measured monoisotopic value against a calculated average, or the reverse, gives a mismatch that grows with chain length and means nothing.

Why larger peptides show a series of peaks

Electrospray ionisation adds protons rather than removing electrons, and a peptide with several basic sites can accept several. The instrument measures mass to charge ratio, not mass, so one substance appears as a series of peaks, each a different charge state, the higher charges at lower m/z.

Two things follow at the bench. First, a spectrum with five peaks is not evidence of five substances. Adjacent members of a charge state series are related by a single proton, and the spacing between isotope peaks within one cluster also reveals the charge: peaks one unit apart mean a single charge, half a unit apart a double charge, and so on. Second, the number you compare against the calculation is the deconvoluted neutral mass, after software has collapsed the series into a single value. Matrix assisted laser desorption usually gives predominantly singly charged ions instead, which is why spectra of the same peptide from the two techniques look so different.

Reading a small fixed difference

A measured mass that sits a small, consistent amount away from the calculation is usually informative rather than alarming. The common offsets:

Difference Usual interpretation
+16, or a multiple of it Oxidation, most often at methionine or tryptophan
+22 Sodium adduct, a proton replaced by sodium
+38 Potassium adduct
+1 Deamidation of an asparagine or glutamine residue
-18 Loss of water
-17 Loss of ammonia, including pyroglutamate formation at an N terminal glutamine
+56 A tert-butyl protecting group that survived cleavage
+100 A Boc protecting group that survived cleavage

Adducts are an artefact of the ionisation and of the solvents in contact with the sample, so sodium and potassium species usually appear alongside the protonated form, not instead of it. Oxidation and deamidation are properties of the material. A protecting group still attached is a synthesis issue and should also show as a later eluting peak in the chromatogram, which is why the two methods are read together rather than separately. What each batch is tested for is listed under quality.

What a matching mass does not prove

Mass is a statement about composition, not order. Two peptides built from the same residues in a different sequence have identical mass, and so do isomeric residues such as leucine and isoleucine. A correct mass rules out a great deal. It does not establish the order in which the residues sit.

Where the order itself has to be established, the method is tandem mass spectrometry: the ion of interest is isolated, fragmented along the backbone, and the ladder of fragment masses is matched against the sequence. That is a sequencing experiment rather than a routine identity check.

A short checklist

  • Calculated mass states which terminal chemistry it assumes.
  • Monoisotopic is compared with monoisotopic, average with average.
  • The reported value is a deconvoluted neutral mass, not a raw m/z.
  • Extra peaks are accounted for as a charge state series or as adducts.
  • Any fixed offset is named rather than left as a discrepancy.
  • The spectrum is read next to the chromatogram, not on its own.