Protocol
Protocol: weighing and transferring milligram quantities
6 November 2026 · 5 min read
A balance that reads to a hundredth of a milligram reports everything happening around it, not only the mass on the pan. At this scale the sample is often lighter than the forces acting on it, and a figure that will not settle is usually describing the room, not the material. This note covers the handling that keeps a small transfer honest.
Why the reading drifts
Five things account for most drift at this scale.
Static charge. Dry powders, plastic vessels and gloves all generate and hold charge. A charged sample is attracted to or repelled by the metal around it, and the balance reports that force as mass. This is the reading that creeps steadily one way and never settles.
Air currents. An open door, a fume hood, a vent, a colleague walking past. Draughts press on the pan and change the local pressure around it.
Temperature difference. An item colder than the balance chamber sets up a convection current along its own surface, which presses on the pan, and condenses water out of the air onto itself, which adds real mass. Both show as a reading that climbs while you watch it.
Moisture uptake. Many solids draw water from the air. That mass is genuine, it is simply not the mass of the substance you meant to weigh.
Vibration. A balance sharing a bench with a centrifuge, a stirrer or a compressor is being shaken, and the display goes noisy rather than drifting.
| Symptom | Likely cause | First thing to try |
|---|---|---|
| Creeps one way, never settles | static | ionise, earth, pause |
| Climbs after a cold item is placed | temperature, condensation | equilibrate closed |
| Jumps when someone walks past | draught | close the shield |
| Last digits never stop moving | vibration | move the balance |
| Rises slowly with the door shut | moisture uptake | shorten the open time |
Setting up
- Site the balance on a heavy bench, away from doors, vents and anything with a motor.
- Check the spirit level before the session, not after an odd result. Leave the instrument powered and warmed through, because a cold balance drifts.
- Run the internal calibration, or check against a known weight, before any weighing you intend to rely on.
The transfer, step by step
- Take the vial from storage and leave it sealed until it reaches room temperature. Opening a cold vial pulls moist air onto cold solid.
- Wipe the vial and the vessel with a lint free wipe. Handling raises charge as surely as the material does.
- Place the empty vessel on the pan, close the draught shield, and let the reading settle before taring. Taring on a moving figure writes the drift into every number that follows.
- Open the vial and take the solid with a clean, dry spatula, held close to the vessel so that the fall is short.
- Close the shield, wait for the reading, then record it. Do not reach in to adjust while the display is live.
- Close the vial the moment the transfer is done. Open time is the whole cost here.
- Record what you actually weighed, not what you aimed to weigh.
Weighing by difference
Weighing by difference removes the vessel, and much of the static and buoyancy error with it. Weigh the closed source vial, remove the portion, close the vial and weigh it again. The difference is what left the vial.
The method works because it never asks the balance for a small absolute mass of a charged powder in a light boat. It asks for two readings on the same heavier object under the same conditions, so the errors common to both cancel. It also shows how much material left the vial even if some did not arrive in the vessel, a loss you would otherwise miss.
Static, and what to do about it
Static discharge means giving the charge a path to ground. An ioniser floods the space with air carrying both charges, so the excess on the sample is neutralised within seconds. A metal vessel conducts the charge away when it touches the earthed pan. Antistatic tweezers, earthed mats and raising the humidity in a very dry room work the same way, by letting charge move instead of accumulating.
What does not work: wiping a plastic boat with a dry tissue, which adds charge, and waiting for the figure to stabilise, which it will not.
Hygroscopic solids
A hygroscopic solid takes on water for as long as it is open, and the rate climbs with the humidity of the room. Three consequences follow. The weighed mass overstates the substance. The material left in the vial is spoilt for later. And a drift upwards can be mistaken for static, which sends you after the wrong fix.
Keep open time to seconds rather than minutes, keep the vial closed between transfers, and return it to its stated storage promptly. Where a solvent and a volume will do the job, reconstituting the whole vial and dispensing by volume avoids weighing a small mass altogether. The concentration calculator handles the arithmetic for that route.
Bench checklist
- Vial closed until it is at room temperature.
- Balance levelled, warmed, checked.
- Shield closed for every reading, tare on a settled figure.
- Earth or ionise before trusting a small mass.
- Weigh by difference where the method allows.
- Vial closed again immediately, mass written down with its lot number.
Terms used here are defined in the glossary, and storage statements sit on the catalogue pages.