Orders placed by 14:00 on a business day leave Poland the same day. Free shipping from €100
Product question?Write to us
RUO

All products are chemical reagents for scientific research only. Not for consumption or use in humans or animals. Policy

Protocol

Protocol: labelling vials and keeping a reagent log

16 November 2026 · 5 min read

An unlabelled frozen tube is waste. A tube with a half legible label is worse, because sooner or later somebody will guess what is in it rather than throw it away. Labelling and record keeping are the cheapest parts of bench work and the parts most often done at the end, in a hurry, with cold hands.

The minimum a label carries

Six fields. Anything less and the tube depends on memory.

Field Example Why it is there
Substance BPC-157 obvious at the bench today, not obvious in a box of forty tubes in April
Concentration 2 mg/ml removes the need to reconstruct the arithmetic from the vial size later
Solvent bacteriostatic water an anomaly may belong to the solvent, not the peptide
Lot from the vial label the only link back to the vial and its analytical documentation
Date of reconstitution 2026-11-16 the clock on a solution starts here, not at the date of purchase
Initials AK tells the next person who to ask

Write the substance out in full. An abbreviation that is obvious to the person who wrote it is a riddle to everyone else, and it is the same person who will be away the week the tube is needed.

If the tube is one of a set, add the portion volume as well. It saves opening three tubes to find one with enough in it.

Concentration comes from the labelled mass on the vial and the volume actually added, not from the volume you meant to add. The concentration calculator does that arithmetic.

Writing a label that survives a freezer

Frost, condensation and solvent all attack labels. These survive:

  • labels with an adhesive rated for low temperature, applied to a dry tube at room temperature
  • cryogenic tape, pressed down along its whole length
  • solvent resistant permanent markers, the kind that hold up to ethanol and isopropanol

These do not:

  • ordinary office labels and masking tape, whose adhesive goes brittle and lifts at a corner, so the label is loose in the bottom of the box by spring
  • ballpoint and gel pens, which skip on polypropylene and leave a line you can rub off with a glove
  • whiteboard markers, which are designed to be wiped off and will be
  • plain paper labels printed at a desk, which smear as soon as a thawing tube sweats

The application matters as much as the material:

  1. Label before filling, while the tube is dry and at room temperature. Adhesive will not bond to a frosted tube.
  2. Write on the body as well as the cap. A storage box shows you caps, a bench rack shows you bodies, and caps get swapped during a busy thaw.
  3. Press the label down along its full length, especially the trailing edge, which is where peeling starts.
  4. Let the ink dry before the tube goes anywhere cold.
  5. Check the label is still readable each time you take the box out. Rewrite it the moment it is not.

The reagent log

A label identifies a tube. The log explains where it came from. One entry per reconstitution, written as it happens.

An entry holds:

  • date and initials
  • substance, lot and the labelled mass on the vial
  • solvent and the volume added, with the resulting concentration
  • number of portions made and the volume of each
  • storage location, down to the box and the position in it
  • anything unusual: a cake that looked different, a slow dissolution, a tube that had to be remade

That last line is the one people skip and the one that earns the log its place. When two experiments disagree months apart, the log is the only record that can tell you whether they shared a lot, a solvent or a thaw.

Lot numbers are the hinge of the whole system. They connect a tube on a rack back to the documentation that came with the material, which is covered on the quality page. A tube with no lot in the log is a tube that can never be traced back.

A log that is not at the bench is not kept

This is the practical rule. An entry written an hour later is written from memory, and memory supplies the volume you intended rather than the volume you used.

Keep the log in the room where the work happens, open, on the surface where the work happens. A bound notebook with numbered pages beats loose sheets, which go missing, and beats a spreadsheet on a laptop in another office, which gets filled in on Friday from recollection or not at all. If the records must end up digital, write at the bench and transcribe afterwards, keeping the original.

What goes wrong

  • Ambiguous dates. 03/04/2026 is two different days depending on who reads it. Pick one unambiguous format, such as 2026-11-16, and use it everywhere.
  • Recording the plan instead of the event. If you added 4.8 ml because the pipette stopped there, the log says 4.8 ml.
  • The tube that was “only one tube”. Unlogged tubes are the ones that turn up unexplained.
  • Stale locations. Moving a box without updating the log converts a precise record into a search.
  • Two handwritings, two conventions. Agree the field order and the units once, and keep a filled example taped inside the front cover.

A short checklist

  • Label before filling, on a dry tube at room temperature.
  • Six fields: substance, concentration, solvent, lot, date, initials.
  • Freezer rated label plus a solvent resistant marker, on the body and the cap.
  • Log the reconstitution while the pipette is still in your hand.
  • One date format, one field order, for the whole log.