CBL-514 in the laboratory
Identification
CBL-514 is listed in the metabolic research section of the catalogue and supplied as a lyophilised solid, freeze dried under vacuum and sealed under a stopper so that it arrives as a dry cake rather than a solution. It is carried as a single component item, which means it is not offered inside any blend and the figure printed on the vial is the whole of its contents. Release is against a purity specification of 99 percent or higher, and the identity and purity results for any one vial are set out in the analytical documentation held for its lot.
The item is offered in three sizes, 5 mg, 10 mg and 20 mg, and the choice between them is really a choice about how the work is organised rather than about price. A programme that runs over weeks is better served by one 20 mg vial than by four smaller ones, because every result then rests on the same lot and batch to batch variation stops being a candidate explanation when two experiments disagree. A first evaluation points the other way: 5 mg is enough to establish how the material dissolves and behaves on your own system, and a small opened stock will not sit on the shelf.
One habit is worth building whichever size you order. Decide the reconstitution volume before the vial leaves the freezer, write that figure and the resulting concentration on the label as soon as the solvent goes in, and portion the stock immediately. Almost every uncertainty that surfaces later about a peptide or small molecule stock comes down to a vial whose history was never written down.
Analytical control
Two determinations stand behind each released lot. Purity is measured by reversed phase high performance liquid chromatography, with the main peak integrated against the whole chromatogram so that related substances and residues of synthesis are resolved from the intended material; the specification applied is 99 percent or higher. Identity is established by mass spectrometry on the same batch. Both belong to that lot alone, which is why the lot paperwork rather than this page is the document that describes your vial.
Reconstitution and solubility
Allow the vial to reach room temperature before the seal is broken. Run the solvent slowly down the inner wall of the glass instead of directing it at the solid, then swirl gently until the liquid is clear. Shaking is counterproductive: it raises foam and leaves material on the stopper and in the neck. Hold the vial up to a light and satisfy yourself that nothing remains undissolved before anything is drawn. Sterile water, bacteriostatic water and a dilute acetic acid solution are the solvents in routine use.
| Vial | Solvent added | Resulting concentration |
|---|---|---|
| 5 mg | 1 mL | 5 mg/mL |
| 10 mg | 2 mL | 5 mg/mL |
| 20 mg | 4 mL | 5 mg/mL |
| 20 mg | 10 mL | 2 mg/mL |
Storage and stability
Keep sealed vials at minus 20 degrees Celsius with the light excluded, and take one out only when the work is actually scheduled rather than cycling the stock in and out of the freezer. Give the vial time on the bench to reach room temperature before the stopper is pierced, so that atmospheric moisture does not condense onto cold solid. Reconstituted material is held at 2 to 8 degrees Celsius, split into portions when it is made up and dated on the label.
Use in the laboratory
The reagent is supplied for in vitro work and for use as a reference material in analytical method development, including calibration and system suitability runs. Metabolic research is the field in which it appears, and that is where the catalogue lists it. Difania supplies the material and the analytical documentation belonging to its lot; the company does not advise on experimental design, and the conditions, controls and endpoints remain the responsibility of the laboratory performing the work.
Safety and handling
Residues, rinses and contaminated consumables are disposed of according to the rules of your institution and the waste regulations that apply locally. Wear gloves and eye protection while the vial is open and while solutions are being prepared, and handle the dry solid where airborne dust can be contained, as its hazards are not fully characterised. The material is a laboratory chemical: not a medicinal product, not a food, not a supplement, not a cosmetic, not for consumption, and not for administration to humans or animals.
Lot documentation
A lot number appears on the label of every vial. Quoting it allows Difania to retrieve the analytical documentation held for that batch. Record the number in the laboratory notebook alongside the date the vial was opened, and any result reviewed later can be matched back to the precise material it came from.
